How To Tie Your Ghillie Brogues

Background of the Ghillie Brogues:

Originally, gillie brogues were simply a flat piece of leather with holes poked along the edges then laced at the top of the foot. Obviously not footwear for royalty! In fact, the word ghillie in Gaelic can be paraphrased as "young boy." (Brogue is translated "shoe.") In other words, if someone tells you that they are wearing "ghillies" on their feet, you are entitled to laugh! Nonetheless, it's common for pipers to refer to these special shoes as "ghillies" as a shortened term.

These days, ghillie brogues appear at first glance to be a dress shoe with the tongue removed. In fact, some pipers do exactly that—whether it be for comfort or economy. But to look the best, a real set of ghillie brogues can't be beat.

There are a number of different brands of ghillie brogues on the market and there can be a significant difference in the weight of the shoes as well as slightly different cuts of the shoes. (I bought a second pair to replace another pair that wasn't compatible with my foot geometry—they hurt my ankle—and found the new pair to be delightfully light in comparison. Great for parades!) You may wish to try on a few different brands when acquiring new shoes. Also when purchasing shoes, keep in mind that with some shoes the soles are only glued (which typically will be adequate for mild weather), while others' soles are stitched for durability (these can hold up better in the extremes of very hot and very wet weather).


How To Tie Your Ghillie Brogues:

Step 1.
Twisting the laces. This shows six twists.

For the front of your shoe, pull the laces reasonably tight—make sure there isn't slack back and forth through the eyelets—then twist them around each other. The number of twists (half rotations) usually numbers between three and six. If the twists are too loose, they look floppy and your laces may slip later. If they are too tight, the laces become an unpleasing jubbled mass of laces. I should note here that some pipers prefer to do a half-hitch with the laces prior to doing any twists—others don't.

 

Step 2.
The twisting at the back. This shows two twists.

Note here that the laces are pulled artificially high in the front and will be lowered for final tying. This view is looking back over your right shoulder with your toe resting on the ground.

At the rear of your leg, pull the laces tight then again twist them around each other. The number of twists usually numbers between 2 and 4 turns—though some do no turns at all. The only real rule is to have less turns in the back than the front. Again, some pipers prefer to do a half-hitch with the laces in the back prior to doing any twists—others don't.

 

Step 3.
Tie your knot.

Some—many competing drum majors, for instance, they like things symmetrical—tie the bow on the front, others—like myself, arguably more traditional—tie it on the side. The pipers in the Scottish regiments tie the knot directly under the flash. Regardless of where you place your bow, do a typical half-hitch prior to tying the bow as you would when tying a regular shoe.

Some pipers make the mistake of tying the laces too high up the leg. It should wrap no more than a couple of inches above the ankle bone. Better too low than too high.

If you end up with lots of extra lace, you can wrap the laces once again around your ankle. Another option, depending on the construction of your tassels, would be to cut the laces shorter then resecure the tassels—these are also called "toggles"—on the ends.

If you want really exacting control over the length of your dangling tassels once the knot is tied, you can go back and make the length of lace on one side of the untied shoe longer than the other—3" to 4" longer can work well. Most pipers don't bother with this, but if you are a perfectionist and the lengths for the bow aren't exactly right to you, it's a good solution.

Slipping Laces.

If you find that your laces slip down over the course of a day, and you aren't just tying them too high on your leg, you have a few options. First would be just to live with the inconvenience and just retie them as needed. Second, pull them very tight, though this can be uncomfortable after a relatively short time. Yet another option—if you are not limited by a band uniform requirement—would be to purchase a pair of heavily textured hose to help support the laces. Yet another possibility is to try flat laces if you are using round laces, as flat laces will behave differently. Still another option is to use a small safety pin on the inside of your hose and slip the pin through the laces knot to secure it in position—if you don't mind a small safety pin resting against your skin for a while. But most pipers, if they don't tie the laces too high, don't have a slipping laces problem.